Transit FireNet Workflow for Azure

Aviatrix Transit FireNet allows you to deploy firewall functions for the Aviatrix Multi-Cloud Transit architecture. With the Transit FireNet feature, the Firewall Network (FireNet) function is integrated into the Aviatrix Transit gateway.

Aviatrix Transit FireNet supports different hashing algorithms available in Azure cloud to load balance the traffic across different firewalls which includes Hash-based distribution mode (five-tuple hash) and Source IP affinity mode (three-tuple or two-tuple hash).

To learn more about Hashing Algorithm and Transit FireNet, read the Transit FireNet FAQ.

To deploy firewall networks in other CSPs:

In this example, a Transit VNet with Aviatrix Gateways is deployed, and two Spoke Gateways (DEV and PROD) are attached to it.

The transit VNET will then have a firewall of supported vendors (Check Point, Palo Alto Networks and Fortinet etc.) deployed within it. Please see the diagram below for more details.

Once the infrastructure is in place you create a policy to inspect the east-west and north-south traffic.


Create Transit VNet

VNets can be created manually on Azure or directly from the Aviatrix Controller.

VNets are created following the Useful Tools Create a VPC guidelines.

  1. Login to the Aviatrix Controller with a username and password.

  2. Navigate to Useful Tools -> Create A VPC.

  3. Select Azure as the Cloud Type.

  4. Add one VNet for Transit FireNet Gateway and select Aviatrix Transit FireNet VNet option as shown below.

  5. Create two more VNets with no option/checkbox selected for Spoke Gateways.


Deploy the Transit Aviatrix Gateway

The Transit Aviatrix Gateway can be deployed using the Transit Gateway Workflow.

Prerequisites for Azure

Transit FireNet builds on the Aviatrix Transit Network solution where Aviatrix gateways are deployed in Transit VNet and/or in Spoke VNet in Azure. ActiveMesh is applied by default.

Make sure the deployment meets the following specifications:

  1. Select the option “Enable Transit FireNet” when launching the Aviatrix Transit Gateway.

  2. Aviatrix Transit Network must be in Connected mode. Go to Multi-Cloud Transit -> Advanced Config -> Connected Transit and ensure the option is enabled.


In Aviatrix Controller version 6.0 and prior, the minimum size of the Aviatrix Transit Gateway virtual machine is Standard_B2ms. Starting in 6.1, the minimum Transit Gateway instance size requirement is removed.


  1. Navigate to Multi-Cloud Transit -> Setup -> Transit -> #1 Launch an Aviatrix Transit Gateway.

  2. Ensure that Azure is the selected Cloud Type.

  3. Enter a Gateway Name.

  4. Select the Azure Access Account Name.

  5. Select a region.

  6. Select the VNet Name.

  7. Select a Public Subnet.

  8. Select a gateway size (default is Standard_B2ms).

  9. Enable Insane Mode Encryption for higher throughputs (optional).

  10. Enable the Transit FireNet function.

  11. Click Create.

  12. Enable Transit Gateway HA by navigating to Multi-Cloud -> Setup -> #2 (Optional) Enable HA to an Aviatrix Transit Gateway.

Please see an example below for Transit FireNet GW:



Insane Mode Encryption for higher throughput requires a virtual machine size. Check this link for details.

Deploy Spoke Gateways

Now that we have an Aviatrix Transit Gateway, we can deploy Aviatrix Spoke Gateways in the spoke VNET using Aviatrix Spoke Gateway Workflow.

  1. Navigate to Multi-Cloud Transit -> Setup -> Spoke -> #1 Launch an Aviatrix Spoke Gateway.

  2. Deploy a Spoke Gateway (GW) in each of the spoke VNETs using defaults while choose correct Account and VNET info.

  3. Choose the Public Subnet.

  4. Enable Spoke Gateway HA by navigating to Transit network -> Setup -> #5 (Optional) Enable/Disable HA at Spoke GW.


Attach Spoke Gateways to Transit Network

Now that Transit and Spoke gateways are deployed, you must connect them.

  1. Navigate to Multi-Cloud Transit -> Setup -> Attach/Detach -> #1 Attach Spoke Gateway to Transit Network.

  2. Select one spoke at a time and attach to the Transit Gateway.



The Transit gateway is attached to Spoke Gateways, but by default, Transit Gateway will not route traffic between Spoke Gateways.

Enable Connected Transit

By default, spoke VNETs are in isolated mode where the Transit will not route traffic between them. To allow the Spoke VNETs to communicate with each other, you must enable Connected Transit by navigating to Multi-Cloud Transit -> Advanced Config. Under Edit Transit, select the Transit Gateway and toggle Connected Transit to Enabled.


Configure Transit Firewall Network

Now that Transit and Spoke gateways have now been deployed, you must deploy and enable the firewall for traffic inspection.

  1. Navigate to Firewall Network -> Setup -> Transit FireNet -> #3a Enable Transit FireNet on Aviatrix Transit Gateway.

  2. Choose the Aviatrix Transit Gateway and Click Enable.


  1. Navigate to Firewall Network -> Policy -> Manage FireNet Policy.

  2. Add Spokes to the Inspected box for traffic inspection.


By default, FireNet inspects ingress (INET to VNET) and east-west traffic (VNET to VNET) only.


Launch and Associate Firewall Instance

This approach is recommended if this is the first firewall instance to be attached to the gateway.

This step launches a Firewall instance and associates it with one of the FireNet gateways.


The Firewall instance and the associated Aviatrix FireNet gateway above must be in the same AZ, and, we recommend that the Management Interface Subnet and Egress (untrust dataplane) Interface Subnet not be in the same subnet.


By default, Aviatrix Transit Firenet uses 5 tuple hashing algorithm but that can be changed to 2 or 3 tuple as per requirement. Please check transit firenet FAQs for more details.

Launch and Attach

In the Aviatrix Controller navigate to Firewall Network -> Setup -> Firewall -> Step 2a. Provide all the required input as shown in the table and click “Launch”.


The vendor’s firewall may take some time after launch to be available.




The Security VNET created in Step 1.

Gateway Name

The primary FireNet gateway.

Firewall Instance Name

The name that will be displayed on Azure Console.

Firewall Image

The Azure AMI that you have subscribed.

Firewall Image Version

Firewall supported software versions.

Firewall Instance Size

Firewall virtual machine size.

Management Interface Subnet.

Select the subnet whose name contains “gateway and firewall management”

Egress Interface Subnet

Select the subnet whose name contains “FW-ingress-egress”.


Applicable to Azure deployment only. “admin” as a username is not accepted.

Authentication Method

Password or SSH Public Key


Applicable to Azure deployment only.

Key Pair Name (Optional)

The .pem file name for SSH access to the firewall instance.

Attach (Optional)

By selecting this option, the firewall instance is inserted in the data path to receive packet. If this is the second firewall instance for the same gateway and you have an operational FireNet deployment, you should not select this option as the firewall is not configured yet. You can attach the firewall instance later at Firewall Network -> Advanced page.

Advanced (Optional)

Click this selection to allow Palo Alto firewall bootstrap files to be specified.

Check Point Specifications

The Check Point Security Gateway has two interfaces as described below.

Check Point VM interfaces


Inbound Security Group Rule

eth0 (on subnet -Public-FW-ingress-egress)

Egress or Untrusted interface

Allow ALL

eth1 (on subnet -dmz-firewall)

LAN or Trusted interface

Allow ALL (Do not change)

Note that security gateway eth1 is on the same subnet as Firenet gateway eth2 interface.

Check Point Security Gateway launch from the Aviatrix Controller automatically initiates the on-boarding process, configure security gateway interfaces and program RFC 1918 routes. After completing this step, user should be able to login to the Check Point Gaia console with username admin and provided password during launch.


Repeat Step 2a to launch the second security gateway to associate with the HA FireNet gateway. Or repeat this step to launch more security gateways to associate with the same Firenet gateway.

Follow Check Point Example to see how to launch Check Point Security Gateway in Azure, and for more details.

Palo Alto VM-Series Specifications

Palo instance has three interfaces as described below.

Palo Alto VM interfaces


Inbound Security Group Rule

eth0 (on subnet -Public-gateway-and-firewall-mgmt)

Management interface

Allow SSH, HTTPS, ICMP, TCP 3978

eth1 (on subnet -Public-FW-ingress-egress)

Egress or Untrusted interface

Allow ALL

eth2 (on subnet -dmz-firewall)

LAN or Trusted interface

Allow ALL (Do not change)

Note that firewall instance eth2 is on the same subnet as FireNet gateway eth2 interface.

You can launch the Palo Alto VM Series firewall from the Aviatrix Controller and then configure it. User should be able to login to the VM-Series console with given username and password during launch.


For Panorama managed firewalls, you need to prepare Panorama first and then launch a firewall. Check out Setup Panorama. When a VM-Series instance is launched and connected with Panorama, you need to apply a one time “commit and push” from the Panorama console to sync the firewall instance and Panorama.


If VM-Series are individually managed and integrated with the Controller, you can still use Bootstrap to save initial configuration time. Export the first firewall’s configuration to bootstrap.xml, create an IAM role and Bootstrap bucket structure as indicated above, then launch additional firewalls with IAM role and the S3 bucket name to save the time of the firewall manual initial configuration.

Fortinet FortiGate Specifications

FortiGate Next Generation Firewall instance has two interfaces as described below.

FortiGate VM interfaces


Inbound Security Group Rule

eth0 (on subnet -Public-FW-ingress-egress)

Egress or Untrusted interface

Allow ALL

eth1 (on subnet -dmz-firewall)

LAN or Trusted interface

Allow ALL (Do not change)


Starting from Release 6.2, FortiGate bootstrap configuration is supported.

Please refer to FortiGate Azure Configuration Example for more details.

Associate an Existing Firewall Instance

This step is the alternative step to Step 2a. If you already launched the firewall (Check Point, Palo Alto Network or Fortinet) instance from Azure Console, you can still associate it with the FireNet gateway.

In the Aviatrix Controller navigate to Firewall Network -> Setup -> Step 2b and associate a firewall with the correct FireNet Gateway.

Vendor Firewall Integration

Vendor integration dynamically updates firewall route tables. The use case is for networks with RFC 1918 and non-RFC 1918 routes that require specific route table programming on the firewall appliance.

  1. In the Aviatrix Controller, navigate to Firewall Network -> Vendor Integration -> Firewall. Select the Firewall Vendor Type and fill in the details of your firewall instance.

  2. Click Save.

  3. You can click Show or Sync to show the integration details, or sync the configuration with the firewall.


Aviatrix Controller automatically programs RFC 1918 in Check Point Security Gateway at a time of launch. This step can be skipped for Check Point if non-RFC 1918 routes programming is not required in Security Gateway.


Vendor integration is not supported for FortiGate. User needs to configure RFC 1918 static routes manually in FortiGate firewall.

Enable Health Check Policy in Firewall

Aviatrix Controller uses HTTPS (TCP 443) to check the health of firewall every five seconds. You must enable this port in the firewall as per given instructions.

Check Point

By default, HTTPS or TCP 443 is allowed in Security Gateway. No action is required.

Palo Alto Network (PAN)

By default, VM-Series does not allow HTTPS or TCP 443 port. Follow these steps to enable it:

  1. Login to VM-Series with username and password.

  2. Go to Network -> Interface Mgmt under Network Profiles and click “Add”.

  3. Give any name in “Interface Management Profile”, check HTTPS checkbox under Administrative Management Service and click “OK”.

  4. Attach Profile with LAN interface. Network -> Interfaces -> Select LAN Ethernet Interface -> Advanced -> Management Profile -> Select appropiate profile.


See an example screenshot below how to attach profile to an interface.


Firewall health check probes can be verified in Monitor -> Traffic.


Fortinet FortiGate

You must allow HTTPS or TCP 443 port in the FortiGate firewall to monitor the health of firewall. Please follow the steps to allow HTTPS in FortiGate:

  1. Login to FortiGate’s console using username and password.

  2. Go to Network -> Interfaces, select port 2 and click “Edit”.

  3. Check HTTPS checkbox under Administrative access -> IPv4 and click “OK”.


The health check probes can be verified in FortiGate by navigating to Log & Report -> Local Traffic.


Example Setup for “Allow All” Policy

After a firewall instance is launched, wait for 5 to 15 minutes for it to come up. Time varies for each firewall vendor. In addition, please follow example configuration guides as below to build a simple policy on the firewall instance for a test validation that traffic is indeed being routed to firewall instance.

Palo Alto Network (PAN)

For basic configuration, please refer to example Palo Alto Network configuration guide.

For implementation details on using Bootstrap to launch and initiate VM-Series, refer to Bootstrap Configuration Example.

FortiGate (Fortinet)

For basic policy configuration, please refer to example Fortinet configuration guide.

Check Point

For basic policy configuration, please refer to example Check Point configuration guide.


There are multiple ways to verify if Transit FireNet is configured properly:

  1. Aviatrix Flightpath - Control-plane Test

  2. Ping/Traceroute Test between Spoke VNETs (East-West) - Data-plane Test

Flight Path Test for FireNet Control-Plane Verification

Flight Path is a very powerful troubleshooting Aviatrix tool which allows users to validate the control-plane and gives visibility of end to end packet flow.

  1. Navigate to Troubleshoot-> Flight Path

  2. Provide the Source and Destination Region and VNET information

  3. Select ICMP and Private subnet, and Run the test


VM instance will be required in Azure, and ICMP should be allowed in security group.

Ping/Traceroute Test for FireNet Data-Plane Verification

Once control-plane is established and no problems are found in security and routing polices, data-plane validation needs to be verified to make sure traffic is flowing and not blocking anywhere.

There are multiple ways to check the data-plane:
  1. SSH to Spoke EC2 instance (e.g. DEV1-VM) and ping other Spoke EC2 to instance (e.g PROD1-VM) to make sure no traffic loss in the path.

  2. Ping/traceroute capture can also be performed from Aviatrix Controller. Go to TROUBLESHOOT -> Diagnostics and perform the test.