Aviatrix Docs :: Documentation

Egress Control Filter

For questions, please see the Egress FQDN FAQ, or learn more about FQDN here.

Aviatrix strongly recommends migrating from Egress FQDN Filtering (Legacy) to the Distributed Cloud Firewall feature in CoPilot 3.11 or greater (also requires Controller 7.1.1710 or greater) to enforce Egress network security policy.

The Egress feature is also available in CoPilot. See the Aviatrix 7.1 documentation for more information.

Configuration Workflow

The instructions below assume there is already an Aviatrix Gateway running in the VPC/VNet where you wish to deploy the FQDN filter. If not, follow the Egress Control workflow to first launch a gateway.

Adding a New Tag

Go Security > Egress Control and click New Tag, as shown below:

Click + New Tag, and enter a name for the tag, for example, prod-whitelist, as shown below:

Adding More Tags

Repeat the previous steps to create more tags and attach them to the same gateway or different gateways. However, if multiple tags are attached to the same gateway, then the mode (Allow or Deny) must be identical.

Adding a URL List to the New Tag

Enable the new tag and click Edit, as shown below:

Click + Add New to add each URL. A wild card is allowed for HTTP/HTTPS (TCP 443), as shown below. (Action "Update" means to save the rules in the tag. If gateways are attached to the tag, "Update" applies to the rules in the gateways.)

Base Policy

Base Policy is an Action field of a rule. It only applies to a rule whose Whitelist is on TCP port 80 or 443.

The default Action field is Base Policy which means if the tag is an Allow (which is the majority of the use cases), this specific rule is to allow the domain name to pass. For the most part, you should not edit this field.

There is a use case where you want to leverage the Active field. For example, you need to allow most of the FQDN names in salesforce.com except for one domain name, finance.salesforce.com. If salesforce.com provides hundreds of domain names, you would have to allow all of them and you cannot use *.salesforce.com as it will leak finance.salesforce.com.

With the new feature, you can now configure two rules to accomplish filtering out finance.salesforce.com while allowing the rest of salesforce.com supported domain names, as shown below:

Domain Name Protocol Port Action

Domain Name	Protocol	Port	Action
finance.salesforce.com	tcp	443	Deny
`*`.salesforce.com	tcp	443	Base Policy

finance.salesforce.com

tcp

443

Deny

*.salesforce.com

tcp

443

Base Policy

Attaching to Gateways

Click Attach Gateway to attach a gateway to the tag.

When a gateway is attached to a tag, the gateway in the tag will be pushed for enforcement (Whitelist or Blacklist), as shown below:

Repeat this step if you have more gateways that should be attached to this tag.

Exception Rule

Exception Rule is a system-wide mode. Exception Rule only applies to Allowlist.

By default, the Exception Rule is enabled, as shown.

When Exception Rule is enabled, packets passing through the gateway without an SNI field are allowed to pass. This usually happens when an application uses hard-coded destination IP addresses for HTTPS connection instead of domain names.

When Exception Rule is disabled, packets passing through the gateway without SNI field are dropped unless the specific destination IP address of the packet is listed in the Whitelist. The use case could be that certain old applications use hard coded destination IP address to access external services.

To disable the Exception Rule:

Under Egress FQDN Filter, click Global Configs.

fqdn rule disable

Clear the Exception Rule checkbox.
Click Close.

If Blacklist is configured, client hello packets without SNI are allowed to pass as it should not match any rules.

Export

Export allows you to download the configured FQDN rules on a per tag basis, in a human-readable text file format, as shown in the example below:

Import

Import allows you to upload a text file that contains FQDN rules to a specific tag. The text file can be:

The downloaded file from FQDN Discovery.
The download file from Export from a different tag.
A text file in the format compatible to Export.

Edit Source

Edit Source allows you to control which source IP in the VPC/VNet is qualified for a specific tag. The source IP can be a subnet CIDR or host IP addresses. This provides fine-grained configuration.

If Edit Source is not configured, i.e., no source IP address ranges are selected, all packets arriving at the FQDN gateway are applied to the filter tag. However if there are one or more source IP address ranges selected, any packets with source IP addresses outside those ranges are dropped. In this regard, the distinguished Source is exclusive.

For example, one use case is if you have two private subnets in a VPC/VNet: one deploys dev instances and another deploys prod instances. With the Edit Source feature, the dev instances can have different tags than the prod instances.

Edit Source assumes you already attached a gateway to a tag.

To go to the Edit Source page, click Edit Source at Egress FQDN Filter on a specific tag and follow the example in the illustration below. The network shown on the right hand of the panel goes through the FQDN tag filtering while the networks on the left side of the panel are dropped.