Transit Gateway to FortiGate over the Internet Workflow

This is not a common scenario. You would only set up this type of connection if you want to connect an Aviatrix Transit gateway to a firewall that is outside your Cloud service provider (for example, in a branch office or warehouse).
  1. In CoPilot, navigate to Cloud Fabric > Gateways > Transit Gateways.

  2. Create a Transit gateway that will connect to your FortiGate firewall.

  3. To connect the transit VPC gateway to FortiGate, navigate to Networking > Connectivity > External Connections (S2C).

  4. Click +External Connection.

  5. In the Add External Connection dialog, configure the following:

    Field Value

    Connect Public Cloud to

    External Device > BGP over IPsec

    Local Gateway

    Select the Transit gateway you created in step 2 above

    Local ASN

    The BGP AS number the Transit gateway will use to exchange routes with the external device.

    Remote ASN

    Enter the BGP AS number the external device will use to exchange routes with the Transit Gateway.

    Remote Gateway IP

    This is the FortiGate WAN IP.

Ensure that the Local/Remote ASN and the Remote Gateway IP are correct before saving.
  1. Click Save.

  2. Download the configuration.

    The following is a sample configuration based on the Site2Cloud configuration above.

    image4

Configuring the Fortinet FortiGate Firewall

  1. Login into FortiGate and configure it as follows:

    1. Navigate to VPN > IPsec Tunnels.

    2. Click +Create New, and select IPsec Tunnel.

    3. In the VPN Creation Wizard, select the Custom template type.

    4. Populate the fields according to your preferences.

    5. Click Next.

VPN Setup

Field Expected Value

Name

Any name

Template Type

Custom

image5

New VPN Tunnel Tab

  1. Complete the Network fields on the New VPN Tunnel tab as follows:

Network section of New VPN Tunnel tab

Field Expected Value

IP Version

IPv4

Remote Gateway

Static IP Address

IP Address

Public IP address of Aviatrix Gateway

Interface

Select the external port/interface

Local Gateway

Disabled

Mode Config

Unchecked

NAT Traversal

Recommended: Enable

Keepalive Frequency

Any value

Dead Peer Detection

On Demand

400

Authentication section of New VPN Tunnel tab

Field

Expected Value

Method

Pre-Shared Key

Pre-shared Key

In the Pre-shared Key field, enter the value from the Pre-Shared Key row in the downloaded configuration file.

IKE Version

1

IKE Mode

Main (ID protection)

400

Phase 1 Proposal section of New VPN Tunnel tab

Field Expected Value

Encryption

In the Encryption field, enter the value from the Encryption Algorithm row in the downloaded configuration file.

Authentication

In the Authentication field, enter the value from the Authentication Algorithm row in the downloaded configuration file.

Diffie-Hellman Group

Select the appropriate value as per the Perfect Forward Secrecy row in the downloaded configuration file.

Key Lifetime (seconds)

28800

400

XAUTH section of New VPN Tunnel tab

Field Expected Value

Type

Disabled

fortigate10

Phase 2 Selectors > New Phase 2 section of New VPN Tunnel tab

Field Expected Value

Name

Any string value

Comments

Any string value

Local Address

0.0.0.0/0

Remote Address

0.0.0.0/0

400

Advanced section of New VPN Tunnel tab

Click +Advanced to complete the fields listed below.

Obtain the following values from the downloaded configuration file.

Field

Expected Value

Encryption

In the Encryption field, enter the value from the Encryption Algorithm row in the downloaded configuration file.

Authentication

In the Authentication field, enter the value from the Authentication Algorithm row in the downloaded configuration file.

Diffie-Hellman Group

Select the appropriate value as per the Perfect Forward Secrecy row in the downloaded configuration file.

Key Lifetime (seconds)

28800

400

  1. Click OK.

  2. Navigate to Network > Interfaces.

  3. Click on the Tunnel created above (e.g. aviatrix-gatew) and assign the IP address from the downloaded configuration file.

    image14
  4. Click OK.

Configure IPv4 Policy

  1. Navigate to Policy & Objects > IPv4 DoS Policy.

  2. Create two new IPv4 policies:

    1. Outbound traffic

      image15
    2. Inbound traffic

      image16

The reference to port2 in the screenshots should be replaced with your own interface name that represents the internal facing interface.

Be sure to select ACCEPT for Action and select ALL for Service.

IPSec Monitor

  1. In the Fortigate UI, navigate to Dashboard > Network and click the IPsec widget.

  2. Select the Aviatrix tunnel, and click Bring Up.

  3. You can then check the tunnel status in CoPilot under Diagnostics > Cloud Routes.

BGP

  1. In the FortiGate UI, navigate to Network > BGP.

  2. Configure the Local BGP Options as below:

    • RouterID : Tunnel IP address taken from the configuration file downloaded at step3

    • Neighbors: Remote tunnel IP address and ASN

    • Networks: All the networks needs to be advertised via BGP (here 10.0.3.0 is the local network of FortiGate)

      image21
  1. In CoPilot, go to Diagnostics > Cloud Routes > BGP Info to verify the BGP Routes.