Aviatrix User VPN Design for Multi-Accounts and Multi-VPC/VNets

This reference design helps you build an end-to-end secure cloud network, from accessing the network (AWS VPC, Azure VNet, or GCP VPC) by users to routing packets among the VPC/VNets, such that once a user is connected via VPN, she can access any private resources in the cloud no matter where that resource is.

There are three use cases covered, from simple to more complex ones. You can read and decide which one suits you or combine parts from different ones to create a network that meet your requirements. You can easily build a full-mesh network.

Multiple VPC/VNets in One Region

The network you have in mind is shown below where all VPC/VNets are in the same region. The Aviatrix Platform instance can be in the same VPC/VNet or a different VPC/VNet.

images0

Assume you have created 4 VPC/VNets in the same region (us-west-2 in this case). You would like to use the VPC/VNet with CIDR 172.31.0.0/16 to host gateways where users connect to. After a user connects to this VPC/VNet via SSL VPN, she should be able to access any instances in the other VPC/VNets as long as her profile allows, without having to connect to each VPC/VNet with SSL VPN.

Another requirement is split tunnel mode, that is, only traffic destined to the cloud goes through the SSL tunnel. If a user does general browsing on the Internet or watches movies from Hulu, traffic should be routed via WI-FI to ISP to Internet. You do not wish to pay AWS for this type of compute and network cost.

Configuration Workflow

Tip: Hover your cursor over the fields to see their definitions. Do a software upgrade if an upgrade alert message appears on your dashboard page.

The description in the steps below provides critical fields you need to select; it may not include all fields. Make sure you have the correct VPC/VNet ID and its region for the VPC/VNet ID field and region in each step.

  1. Launch a gateway with VPN capability in VPC 172.31.0.0/16.

    • Create a VPN Gateway.

    • At the Gateway Name field, enter a distinct and convenient name. For

      example, mgmt-vpn-1.

    • Select VPN Access. Selecting features in the Advanced Options section is not required. Selecting Split Tunnel Mode is not required.

    • Select Save Template, if you wish to do so. This template saves you from entering:: repeated fields if you wish to create more gateways with the same configuration.

  1. Repeat Step 1 to create more gateways with VPN enabled. Note that each gateway must have a different VPN CIDR Block and name. You may select different AZs for the Public Subnet field.

  2. Configure AWS or Azure peering.

    • Go to Aviatrix Controller > Peering > AWS Peering for AWS or Peering > Azure Peering for Azure. Click *New Peering.

    • For Peer1, select the Account Name, Region, and VPC ID of one of the gateways created.

    • Do the same for Peer2.

    • Click OK. If the new peering does not show up under the list of peerings below the popup, click refresh.

    • Repeat the above steps as many times as necessary for the gateways you created.

  1. Add Users and Profiles.

    • Go to Cloud Fabric > UserVPN > select the Profiles tab to create as many profiles as you please. The target field can be FQDN (DNS names or fully qualified domain name).

    • Go to Cloud Fabric > UserVPN > select the Users tab to add more users. Associate each user with a profile. Note that if no profile is associated, the user has full access to all resources. When a user is added to the database, an email with a .ovpn file or .onc (for Chromebooks) will be sent to the user with detailed instructions.

  1. Launch VPN connections from remote users to VPC/VNet1 (172.31.0.0/16). Once the SSL VPN connection is established, this VPN user should be able to reach all instances (in all VPC/VNets) to which he/she has access permission.

Multiple VPC/VNets in Multi-Regions, Split Tunnel

The network you have in mind is shown below where VPC/VNets are in different regions. The Aviatrix Platform instance can be in the same or a different VPC/VNet.

images1

In this example, Aviatrix encrypted peering is used for connecting to remote VPCs. You can also use AWS peering/Azure peering to accomplish the task.

Assume you have created 4 VPC/VNets. You would like to use the VPC/VNet with CIDR 172.31.0.0/16 in us-west-2 to host gateways where users connect to. After a user connects to this VPC/VNet via SSL VPN, she should be able to access any instances in the other VPC/VNets as long as her profile allows, without having to connect to each VPC/VNet with SSL VPN.

Another requirement is split tunnel mode, that is, only traffic originating from the user and destined to resources in VPC/VNets is routed through the SSL VPN tunnel. The traffic to the Internet will be routed through ISP instead of SSL VPN tunnel.

Configuration Workflow

Tip: Hover your cursor over the fields to see their definitions. The description in each step does not include all fields. Make sure you have the correct VPC/VNet ID and its region for the VPC ID field and region in each step.

  1. Launch a gateway with VPN capability in VPC 172.31.0.0/16.

    • Create a VPN Gateway.

    • At the Gateway Name field, enter a distinct and convenient name. For

      example, mgmt-vpn-1.

    • Select VPN Access.

    • Use the default VPN CIDR Block.

    • Select Split Tunnel mode.

      1. For the Additional CIDRs field under Split Tunnel, enter other VPC/VNet or any network CIDRs you wish to reach beyond the VPC/VNet you are connecting to. In the example shown, you should enter 10.10.0.0/16,10.5.0.0/16,10.80.0.0/16. It is a good idea to do some planning to include future VPC/VNets or network address ranges. (In a case where you never have to worry about connecting to your corporate VPN, you may consider entering the entire private network address range in the Additional CIDRs range field, separated by commas: 172.16.0.0/12,10.0.0.0/8,192.168.0.0/16. Doing so affords you to not have to reconfigure the gateway if you need to add more VPC/VNets for networking with different CIDR range in the future.)

      2. (Optional) If you like to use private DNS name to access instance, you can fill the Nameservers and the Search Domain field under Split Tunnel. Enter your private DNS name and search domain. If you use AWS Route 53 private hosted zone and records for your host names, make sure the Nameserver is the DNS server of the VPC/VNet. In this case, you should enter "172.31.0.2".

    • Select Enable ELB.

    • Select Save Template. This Template saves you from entering

      repeated fields if you wish to create more gateways with the same configuration.

  1. Repeat Step 1 to create more gateways with VPN enabled. You may select different AZs for the Public Subnet field.

  2. Build encrypted routing networks to reach other VPC/VNets.

    • Launch a gateway without VPN capability in VPC/VNet 172.31.0.0/16. This:: is the routing gateway. Make sure:

      1. At Gateway Field, give it a distinct and convenient name. For example, dev-east-1, or teamKardashian-east-1 for the Kardashian game project.

      2. VPN Access is not selected.

      3. Enable NAT is NOT selected (since step 1 has enabled NAT function for this VPC/VNet).

      4. Save Template is not selected. (so that you don’t overwrite the hard work of entering the fields of gateways with VPN enabled).

    • Repeat step 3 for VPC/VNet 10.10.0.0/16, 10.5.0.0/16 and 10.80.0.0/16.

      Select Enable NAT if you want instances in these 3 VPC/VNets to be able to reach the Internet directly.

    • Configure encrypted peering. Note

      that each VPC/VNet is represented by one or more gateways. Make sure you want to peer between two gateways without VPN capability.

  1. (Optional) Set up Stateful Firewall Rules at the VPC/VNet level.

    • Select the gateway you just created to edit Security

      Policies to add any policies for each VPC/VNet.

  1. The steps above complete the network infrastructure setup.

  2. Add Users and Profiles.

    • Go to Cloud Fabric > UserVPN > select the Profiles tab to create as many profiles as you

      please. The target field can be FQDN (DNS names or fully qualified domain name).

    • Go to Cloud Fabric > UserVPN > select the Users tab to add as many users as you please.

      Associate each user with a profile. Note that if no profile is associated, the user has full access to all resources. When a user is added to the database, an email with an .ovpn file or .onc (for Chromebooks) will be sent to the user with detailed instructions.

Multiple VPC/VNets in Multi Regions, Full Tunnel, your own firewall

The network you have in mind is shown below where VPC/VNets are in different regions. The Aviatrix Platform instance can be in the same or a different VPC/VNet.

images2

Assume you have created 4 VPC/VNets. You would like to use the VPC/VNet with CIDR 172.31.0.0/16 in us-west-2 to host gateways where users connect to. After a user connects to this VPC/VNet via SSL VPN, she should be able to access any instances in the other VPC/VNets as long as her profile allows, without having to connect to each VPC/VNet with SSL VPN.

Another requirement is full tunnel mode, that is, all traffic originated from the user is routed through SSL VPN. Your organization requires to run its own firewall function for any Internet-bound traffic.

Configuration Workflow

Tip: Hover your cursor over the fields to see their definitions. The description in each step does not include all fields. Make sure you have the correct VPC/VNet ID and its region for the VPC/VNet ID field and region in each step.

  1. Create a VPN Gateway in VPC/VNet 172.31.0.0/16.

    • Create a VPN Gateway.

    • At the Gateway Name field, give it a distinct and convenient name.

      For example, mgmt-vpn-1.

    • The VPN CIDR Block must be a subnet that is outside your current

      VPC/VNet CIDR range and your laptop or device subnet range. In the example above, you may enter 192.168.2.0/24.

    • Full Tunnel Mode is selected.

    • Enable AWS ELB is selected.

    • Enable Policy-Based Routing (PBR) is selected.

      1. Note that the PBR Subnet must be a subnet that is in the same AZ as* the primary subnet (Public Subnet where the gateway is launched). Enter the AWS subnet default gateway for PBR Default Gateway field. For example, if PBR Subnet is 172.31.48.0/20, the default Gateway field is 172.31.48.1.

      2. (optionally) you can enable NAT Translation Logging to log* every user’s each activity to every server and site. This is useful for auditing and compliance.

      3. Save Template is selected. This Template saves you from entering repeated fields if you wish to create more gateways with the same configuration.

  1. Repeat Step 1 to create more gateways with VPN enabled. You may select different AZs for the Public Subnet field.

  1. (Optional) If you have your own routing network to route between the VPCs and one of your own backbone routers can route traffic to your own firewall for Internet-bound traffic, you can skip this step and the next two steps (step 4 and 5).

Launch a gateway without VPN capability in VPC 172.31.0.0/16* This is the routing gateway, make sure:

  1. At the Gateway Field, give it a distinct and convenient name. For example, dev-east-1, or teamKardashian-east-1 for the Kardashian game project.

  2. Enable NAT is not selected.

  3. VPN Access is not selected.

  4. Save Template is not selected. (so that you don’t overwrite the hard work of entering the fields of gateways with VPN enabled).

  1. (Optional) Repeat step 3 for VPC 10.10.0.0/16, 10.5.0.0/16 and 10.80.0.0/16. Select Enable NAT if you wish the instances in these VPCs to be able to reach Internet directly.

  2. (Optional) Configure encrypted peering. Note: each VPC/VNet is represented by one or more gateways. Make sure you want to peer between two gateways without VPN capability.

  3. The steps above complete the network infrastructure setup.

  4. Add Users and Profiles.

    1. Go to Cloud Fabric > UserVPN > select the Profiles tab to create as many profiles as you please. The target field can be FQDN (DNS names or fully qualified domain name).

    2. Go to Cloud Fabric > UserVPN > select the Users tab to add as many users as you please. Associate each user with a profile. Note: if no profile is associated, the user has full access to all resources. When a user is added to the database, an email with a .ovpn file or .onc (for Chromebooks) will be sent to the user with detailed instructions. Alternatively, you can go to download the .ovpn file directly.

Use an AWS Transit Gateway to Access Multiple VPCs in One Region

You can use an AWS Transit Gateway (TGW) allow remote users to connect to multiple VPCs in the same region, as shown below.

vpn_with_tgw_one_region

User VPN Solution for Multi Cloud

With Aviatrix multicloud support, you can build a global VPN solution that spans to multi cloud.

vpn_tgw_multi_cloud